Dutton Dementia

[Mick O'Malley]

This morning I carried the rear body down to the cave and heaved it into position on the frame. I thought I'd make it look a bit more like a car by putting the back lights in. Digging them out of my shed and examining them revealed that they would need quite a bit of work in the location department, so I quickly abandoned the 'car' option and reverted to 'trailer'. Using a length of the ever handy paracord I tied the trailer board securely in the number plate recess of the body moulding, where it sat nicely. Threading the seven pin plug and its lead through to the frame's front, and admiring my handiwork, it dawned on me that reflective triangles would be needed .



I thought I could use tech screws into the newly cleared rivet holes to secure the moulding, but the holes were too big for the 5.5 mm items I had. A search revealed that 6.3mm ones were available, but in a minimum of 100, and as I would only need eight I decided to run a tap through the holes and screw it home that way pro-tem. I lashed out the almost four quid for the triangles and called it a day.

Regards, Mick

[Dpaz]

Mick, I may be wrong but, if you are towing something you need the towing vehicle's reg on the trailer and the towed vehicle covered so that your untaxed " trailer" doesn't trigger the ANPR cameras and get you tickets for 2 vehicles.
It is coming on well.

[Mick O'Malley]

Hi Dpaz,

Thanks for that. My Jazz is kosher, so I don't think I'll be in any ANPR danger. I think the only circumstance in which I would fall foul of the persons in blue would be if I were pulled by a real jobsworth. When collecting my Mk1 Marlin Roadster on tow from Birmingham on a Sunday morning a good twenty years ago, we passed a jam sandwich plotted up on a roundabout. Despite its not having a windscreen, and being both open and unpainted, they scarcely gave it a glance. A pull would have been interesting, as my full harness belts were simply draped over my shoulders to give the illusion of safe Marlin piloting. Happy Days!

Regards, Mick

[Mick O'Malley]

After what seemed an interminable fight with my camera, which would suddenly no longer communicate with my PC through its supplied cable, I uploaded my latest pictures using an SD card reader. Hooray!

Anyway, the day before yesterday, before my mentally exhausting camera battle (I'm no sort of techie, a telephone, to me, is made of Bakelite and sits on the hall stand) I wandered down to the cave, wheeled the partially clothed skeleton most of the way out of the cave and took off the rear body moulding. Offering up my 6mm tap to the old rivet holes revealed perfect compatibility, so I set to cutting the threads at all ten attachment points, the six side ones needing the wheels taking off. Thinking forward to the time when permanent attachment of the moulding would be necessary, and noticing the pristine 7mm tap in my set, which also has a 1mm pitch (the 6mm has seen a great deal of action over the years and looks due for replacement), I thought maybe I'd open the holes out further for greater peace of mind. A quick Ebay search revealed that 7mm screws and washers must be made (judging by the horrendous prices), not of the advertised stainless steel, but of Platinum plated Unobtanium, so that idea was swiftly abandoned.



Popping the rear body back on I then fitted the newly purchased reflective triangles, screwing them to bespoke lengths of batten though the rear lamp cluster holes. Approaching dusk decided the camera to employ flash, nicely demonstrating the efficacy of the rear end gubbins - not that I'll be towing at night!



Since then I've purchased a Spitfire centre rear deck filler cap, its fittings, and a short length of the necessary 2" pipe which will be welded into the top of the Cortina fuel tank, bridging the gap, the old filler being chopped off and a blanking plate welded in its place.

Regards, Mick

[Mick O'Malley]

Today, looking at the dismal weather, I decided to not venture down to the cave, but then remembered that the bits I'd ordered for the modified filler position had arrived yesterday so I might as well do a little offering up. I retrieved the tank from my shed and slid it into the boot, where it will eventually live. However, the boot floor had been so comprehensively butchered for the previous giant tank I'd removed that it had nothing to sit on . OK, what else could I do? I hit on cutting off the Ford filler stub, ready for the resulting hole to be blanked off at some future date. Because of its angle and proximity to the tank's flange, it didn't lend itself to an easy attack. Trying it with each in turn of the four sides of the flange trapped in my Workmate I managed to start the necessary hacksaw cut. I got about two thirds of the way through before the saw's frame started hitting either the flange or the tank's body, so I took out the blade, made a grip at one end of it with gaffer tape, and finished off the cut. Neither easy nor finger friendly!



I gently filed clean the cut edge, gaffer taped over the hole, and called it a day, pleased that I'd at least done something .

Regards, Mick

[Mitchelkitman]

Originally Posted by Mick O'Malley

I managed to start the necessary hacksaw cut. I got about two thirds of the way through before the saw's frame started hitting either the flange or the tank's body, so I took out the blade, made a grip at one end of it with gaffer tape, and finished off the cut. Neither easy nor finger friendly!



I gently filed clean the cut edge, gaffer taped over the hole, and called it a day, pleased that I'd at least done something .

Regards, Mick

Well done - I look forward to your updates....... an interesting rebuild.
If it makes you feel any more positive about the sawing today...... A couple of years ago I had to get a cistern off a customer's toilet. Some idiot (a so-called professional) had decided that the 2" x 1" wooden spacer between the cistern and tiles could be attached to both with "no nails". With a hacksaw blade between my fingers, it took 1.5 hours to cut through the adhesive that was holding the cistern to the wood.

[Lucky@LeMans]

Making some good progress there Mick, I wish I could say the same for my project. Your 7mm tap you were intending to use must be a rarity in itself. I've been in engineering for longer than I care to remember but I don't recall ever coming across a 7mm tap or screw / bolt come to that !