Mick O'Malley's Moss Monaco

[Lucky@LeMans]

Wow, that Maserati looks fab ! Is it and original ? It almost looks too perfect.
Chris at Tribute has a buck for one of these, don't think he has taken a mould yet but it is on my radar as a future build !
Some of the shows can be a bit underwhelming that's true but finding a gem like that can make your day !

[Mick O'Malley]

Originally Posted by Lucky@LeMans

Wow, that Maserati looks fab ! Is it and original ? It almost looks too perfect.
Chris at Tribute has a buck for one of these, don't think he has taken a mould yet but it is on my radar as a future build !
Some of the shows can be a bit underwhelming that's true but finding a gem like that can make your day !

The programme reads: No.78 Richard Wilson Maserati 250S 2490cc 1957 Red. If you went for the Tribute, what underpinnings would you go for?

[Lucky@LeMans]

Originally Posted by Mick O'Malley

The programme reads: No.78 Richard Wilson Maserati 250S 2490cc 1957 Red. If you went for the Tribute, what underpinnings would you go for?

A bit of googling and it does appear to be an original !
As for a base car the Maserati has a narrow track and short wheelbase so it lends itself towards a "7" style chassis. Some of engines they used were 4 cylinder twin cams like the Fiat / Lancia / Lotus designs with twin side draught carbs. So a replica under bonnet area could be created too !

[Mick O'Malley]

A few days ago, when weather permitted, I swapped the tacky plastic switch for the 'Repro Lucas' item I'd bought on Ebay. It has a galvanised looking finish, unlike the chrome original, and the mechanism behind is encased in a soft plastic shell rather than the hard black plastic of the Lucas item. Only time will reveal if it will A) tarnish and/or B) fail early. I'll keep looking for an original on Ebay.



It's the one to the right of the indicator gubbins.

Having fitted the electric fan, I began wondering about the thermostat as I couldn't recall having fitted a new one - a trawl through this blog proving fruitless. There was one fitted, which I removed for testing - it was a dud, refusing to open in a pan of boiling water. Not a lot of good. I ordered a new one c/w gasket and cleaned the mating surfaces of its housing and the top of the water pump. Once it arrived I fitted it, fired her up, and watched in dismay the resulting mini Niagara . I think the problem was the tissue thin gasket. Anyway, I've ordered a couple of new ones and some likely looking gasket goo, having not found a supplier of my reliable six decade standby, Red Hermatite. If all goes well I shall take her to Prescott next Saturday.

Regards, Mick

[Mick O'Malley]

Originally Posted by Mick O'Malley

After posting the above last Sunday, I decided that the very distressed volt meter was rather spoiling the overall effect, so I hit Ebay searching for used same. After ploughing through the plethora of mis-advertised ammeters I found a nicely presented Tudor branded one BIN at a reasonable price which was delivered, very well packed, yesterday.

Not having been successful two days running in using the instant gasket installing the new thermostat - ham-fisted, moi? I set to releasing the LH end of the dash, wedging it open with a block of wood to marginally improve the meagre access, having first disconnected the battery's earth. Despite removing the recently installed switch just above it, I couldn't get enough purchase on the gnurled nut holding it on. OK, remove the fuel gauge immediately below for a try that way. Having done that, which was a struggle in itself, I was just about able to access the nut with long nosed pliers - a squirt of WD40 and lots of cursing and it was off. Having put its replacement in I remembered that a nicer fuel gauge had come with the Phaeton so I dug that out of my box of clocks and substituted it. Reinstating the dash and re-connecting the battery I was delighted, if not amazed, that they both worked a treat. A hat trick of successes was achieved as I'd spotted a dodgy connection in one of the tacho. wires and remade it so said clock now works consistently . No picture as yet.

Today it's back to the thermostat housing problem. Third time lucky? Maybe.

Regards, Mick

[Mick O'Malley]

This afternoon I had another crack at fitting the thermostat housing. Once it was off I began removing all the instant gasket which was stuck like the proverbial to a blanket, first from the housing, then the top of the water pump. It's held in place by two screws, one of which is much longer than the other. I noticed that there was water from yesterday in the longer tapped hole so stuck a screwdriver in to clear the mystery blockage. Not possible, as the sheared remains of the 55 year old screw were stuck halfway down the tapping. I ground a little off the end of the broken screw and fitted it with a plain washer so that it wouldn't bottom in its hole: I think this was probably the fly in the ointment. I also ran a die down it and its oppo as they were fairly rusty. I again cleaned both the mating surfaces with acetone before applying the instant gasket, waited the recommended ten minutes for it to skin over, and reassembled. According to the blurb it takes 24 hours to fully cure, so I won't top up the rad and fire her up until tomorrow. Fingers crossed.

Here's the dash with its replacement clocks, looking much better IMO.



Regards, Mick

[Mick O'Malley]

Yesterday I uncovered the beast and, in true pessimist fashion, topped up the rad. and fired her up. Bingo, not the tiniest trace of leakage. However, there was vapour floating up from the exhaust manifold. I first assumed this was carelessly spilled water soaked into the exhaust wrap and boiling off. No! A quick sniff indicated oil. Aaaaaaaaagh! So, out with the home made ramps kindly donated by my Polish ex-neighbour when he quit the UK.



Worming underneath with a wander light revealed damning evidence of a leak, but from where? I first checked the sump bolts and got a hit: they all needed at least a quarter turn, so I'm guessing that the gasket had shrunk over the years (decades?) of inactivity. Rolling back to earth and the smoke had vanished. Result!

Today's imagined sortie in her failed to materialise as my daughter had inadvertently boxed me in, her mind being elsewhere yesterday, and I didn't want to harass her at stupid o'clock. So, off to Prescott in the tin top. I'd not got far when I fell in behind this top-down Mk1 Sprite which I followed all the way to the venue, the pilot turning out to be a competitor.



There was the usual fabulous assortment in the paddock, which included, to my eye, some real gems. Chief amongst them was this glorious Allard J2 powered by a 3917cc flathead V8 with an overhead inlet valve conversion.



Next was this 1920 Bugatti with a novel front track modification.



Last but by no means least was this 1380cc A series powered A40.



All in all a brilliant day out to round off this year's accessible speed hill climb season. Roll on 2024!

Regards, Mick

[Car photographer]

Originally Posted by Mick O'Malley

The programme reads: No.78 Richard Wilson Maserati 250S 2490cc 1957 Red. If you went for the Tribute, what underpinnings would you go for?

Yes that's real, I was there at castle combe too and spoke to him briefly, I've also photographed that car at silverstone classic too

[Dpaz]

Underpinnings? Got to be a GT6 or Vitess 6 anything less would be sacrilege,no?

[Lucky@LeMans]

Originally Posted by Dpaz

Underpinnings? Got to be a GT6 or Vitess 6 anything less would be sacrilege,no?

Some of the OSCA cars by the Maserati brothers used a Fiat based twincam engine ! The MT4 being a good example. But yes, a straight six would suit it well !