Ah I see

Great start :first:

Cut down both sides here ..V...and along to bottom of the boot extender and overlap the two parts as shown and bond together with Tiger Seal.
http://i1046.photobucket.com/albums/...ountmodded.jpg

Also trim the edge that fits against the original rear panel of the car to clear bumper brackets etc. You will need to cut holes as shown to access cables for rear lights.

Hi Chris,
thanks again :mod:
I give a update tomorrow.
Greets Henry

Day #2
Everything went according to plan.
2x electrics relocated
The rear body kit attached with 2K adhesive
Hinges attached
Petrol cap sized and drilled.
Not much but it`s twice. :roll:
Greets Henry

http://i1217.photobucket.com/albums/...8/Tag2Dach.jpg
http://i1217.photobucket.com/albums/...chluumlsse.jpg
http://i1217.photobucket.com/albums/...2Ausmessen.jpg

Day 3 of the rebuild.
2 Times Relocation of the fuse boxes and the expansion tank
I wanted to put the fuse box "only" inside.
That we did not like, then we cut through all the cables and 12 "extended.
Now it fits perfectly. There are about 30 wires per car and takes 2 hours.
Cut pieces to put in between, solder, insulate and re-wrap.
Tomorrow there is a new update.
regards
Henry

http://i1217.photobucket.com/albums/...boxcutting.jpg

http://i1217.photobucket.com/albums/...locFusebox.jpg

http://i1217.photobucket.com/albums/...ansionTank.jpg

Left hand drive :eusa_wall: You have ABS unit in the way, good solution moving fusebox :biggrin:

Hi Chris,
yes it's just everything on the "other" side.:tea:
Now at the site, I like it also the best.
Tomorrow we start with the front end.:smile:
Love it, thanks again for the MX250 kit.
Greetings from Germany
Henry

Two more images
Tomorrow we will install the lights and mount the hinges (front) of the morris minor
And then we will begin with filling and sanding. How long you need for this “because normally”

http://i1217.photobucket.com/albums/...irecutting.jpg

http://i1217.photobucket.com/albums/...perspindle.jpg

Making rapid progress Henry. Bang on target with your wiper spindle holes too!
As too how long sanding should take......you can take as long as you like! Its the bit I enjoy the most.

HI NicK,
yes it goes ahead.:eusa_dance:
the bit I put over it for the exact angle.
We want to cut out the back window on Sunday.
How wide must be the edge (all around) of the rear window?
I do not want to cut too much:pray:

I laid the glass in position, measured the rubber thickness, which I think, was about 4mm, and added that 4mm all around the glass edge.

Thats what we need,
1000 Thanks:pray:

I have to rebuild the engine hood. because the minor hinges do not fit:eusa_wall:
Has anyone installed the 10 "long?

Greets Henry

Do check your window rubber before cutting. Its +4mm from memory, but I may be wrong!

Hi Heinrich

As Nick says, lay just the glass on the flange and draw around it then mark 4-5mm INSIDE the line, so that the hole is SMALLER than the glass.

Hi Chris, hi Nick,

thanks for the details.

More Images on Monday:gossip:

and my daily question :pray:

has anyone ever installed fog lights in the 2 round holes.

Perhaps the mini one fog lamps will fit?

http://commons.wikimedia.org/wiki/Fi...lift_front.JPG

http://i1217.photobucket.com/albums/...niFoglamps.jpg


Greets Henry

Great idea about the lights, would look cool :eusa_dance:

Hi Chris,
we will try to install the mini Foglamps.

Today, I have rebuilt the cutout for the side window.

A thick rubber gasket I did not want:dizzy:

There was a gap of ~ 30mm between body and window.
Now, the difference was reduced to 2-3mm.
Finally, I start filling.
Now it looks like a car.:laugh:

http://i1217.photobucket.com/albums/...reduce28mm.jpg
http://i1217.photobucket.com/albums/...lessismore.jpg
http://i1217.photobucket.com/albums/...espachtelt.jpg

Great progress mate! Please explain what you had to do on the window gaps

Hi it was easy,
to reduce the gap, I'm just drawn a line outside to the window.
I Cut it Right there.
The sawed-off part of the back and put it fixed.
To get around 3mm space between the window and roof I put on bonding spacers between.
Until the glue was dry I had screwed 2 screws for fixing. Thats it


Sorry for my bad english, I hope you can do something with the instructions.
regards

And my daily update.

http://i1217.photobucket.com/albums/...gefuumlllt.jpg

http://i1217.photobucket.com/albums/...8/Tag9Tank.jpg

Heinrich, how long do you have left? You are nearly done! Are both cars at the same stage? :whoo: