Dual 7" Servo

[peterux]

Originally Posted by peterux

I have a concern about using BMC4052 master cylinders with cars fitted with REAR disk brake callipers that I ought to raise........

..........this may not be the case but I have no way of telling so I thought I should bring this to peoples attention.

Thanks to everyone who considered this potential risk and replied with their views and suggestions above.
I'm still doing some background investigation and I will post an update if I can get anything more definitive.

...peter

[peterux]

Originally Posted by peterux

Thanks to everyone who considered this potential risk and replied with their views and suggestions above.
I'm still doing some background investigation and I will post an update if I can get anything more definitive.

...peter

I got me a copy of the 'well known' workshop manual for the Ford Sierra 1982-1993. (Cost me £2.96 inc. post!).

It has a very comprehensive braking system with full description and types. The good news is that there is not any mention of the dreaded 'Residual Pressure Valve'.
The exploded diagram and overhaul section of the master cylinder is straightforward and shows no sign of any RPV either.


Sierra Brake master by marlinpeter, on Flickr

I am now confident that there is no issue with using the 1982-88 Sierra master cylinder on cars with either drum or disk rear brakes.

...peter

[morris]

cool, glad to hear that peter, The thought of moving on to test M/C number 4 was not fitting in well with my list of other bits to buy

[cabrioman]

Yeah Peter you may be right, it may have just been a costing that influenced the use of 2 or 3 outlet. To be honest its so long since I worked on a Sierra I can't recall the routing of the pipework.

I just wondered if there was an operational benifit to a two feed setup which I hadn't figured out.

[denniswpearce]

Thanks for the offer Jason but my Sportster is due its MOT at the end of the week and its the garage I use for my daily runabout, so I spoke to them today and they are going to purge the system of its trapped air using their compressor as well as carry out the MOT.

So your offer is very much appreciated but not needed.

[Patrick]

hmm lock up would be bad I've not installed yet so no big worry there.

On Richard E36 compact we switched the drums for discs without issue on the back and that been running that way for a number or years now. Could be the BMW master cylinder on there is of a different design though.

[morris]

Hi Peter, just checked eurocar parts for a 1987 1.8 sierra and it offers both drums and disks for the rear. I know they're not much of an authority but it does offer some hope.

Patrick hasn't tried his yet, Robin, have you?

Suck it and see may be the only way to know for sure. I've got mine all installed and have binned the packaging etc so I don't mind charging the system up with fluid to see what happens. I was going to anyway so as to check for leaks. It won't be as good as a rolling test but if the calipers lock on it will still be pretty obvious just by my inability to turn the wheel by hand.

[Chris Cussen]

The standard Sierra (drums rear) set up had a brake limiting valve fitted at the rear of the car and not as part of the master cylinder.

[mashtun]

The Haynes Sierra manual that I have describes it as a "deceleration valve" (and says it was fitted in the engine compartment?), and from what I can tell it seems its purpose was the reverse of a residual pressure valve i.e. it's designed to reduce the pressure to the rear under heavy braking. I didn't fit it to my Cabrio.

If you view the "Hydraulic Actuation" components for 82-86 1.3 & 1.6 Sierras on the Brakes International website and click on the "More Products on Next Page" button at the bottom of the window you'll see a couple of regulator valves (HRV1125 and HRV1069) listed - the HRV1125 looks like the pics in the Haynes manual. The 2.3 V6 had drums at the rear and also has these valves listed.

Peter, have you found anything that describes what form a residual pressure valve inside a master cylinder would take?

Mark.

[GreatOldOne]

Chaps - I think this needless worrying.

I have a Ford 22mm Bore MC, with BMW discs & calipers all round. It works fine!

[cabrioman]

I think Mike is correct, it may be worry about nothing.

It looks to me like the risidual valves are really aimed at preventing excess travel in the brake pedal.

Wilwood provide write ups about their 2lb and 10lb valves for use in drum and disc applications which seem to provide a pretty clear explanation of the use.

Have a look here http://www.wilwood.com/MasterCylinde...derValves.aspx just scroll down the page a bit.

I guess if doubt remains an email to Wilwood disguised as a pre purchase enquiry might shed some light.

I am using the Sierra MCyl designed for drum rears (which is what i have) I know a couple of the guys in the MOC were using the same cyl/brake configuration and then replaced the drums with Sierra rear disc setups. I haven't heard of any issues after they upgraded. The only comment from the MOC BMW Cabrio tech rep was that his car was borderline overbraked at the rear when tested during SVA but I don't think he has had any issues as such.

John

[andrew curtis]

Go onto the italan manufactures web site [ www.cifam.it] they have a lot of information including brake circuits it may be of help.
With regard to my blacksmiths brake tests ref Mikes report i could not get any lock up on the rear brakes, the car does not have any pressure regulating valve in the rear bake line as is standard on the E30 doner
Andrew

[denniswpearce]

Ok I can report on my servo installation now that my local garage managed to purge the system of its trapped air.
I obviously informed the garage owner of what I had done in replacing the metro servo with the dual servo so that he was in the picture.
Firstly their reservoir caps did not fit my reservoir ( same problem I had ), but then they overcame that issue and bled the system of a lot of trapped air.
He said the brakes performed well and he was able to lock the wheels very easily. I drove it home this morning and was anxious to try it for myself.
However, he did give me one bit of advice before I left.
It is a condition of a dual servo that if you pull up at traffic lights and leave your foot on the brake pedal that the travel will be longer than when you are moving, so his advice is not to leave your foot on the pedal when stationary. Fortunately I am one of those who uses my handbrake and not leave my foot on the brake pedal so that I do not blind the driver behind with my brake lights ( not an issue with the Sportster though ).

Anyway, driving down the road from the garage I was very tentative with the pressure but it has a completely different feel to the pedal, the travel is longer and takes a bit of getting used to, but you do not have to apply much pressure before the brakes bite, its very light, more akin to my daily runabout.
Obviously I wanted to stamp on it real hard to see the reaction and I did. The response was an immediate lock up, but it felt like the rear wheels rather than the fronts.
Then I had other cars in the vicinity and could not try that test again. But at junctions and roundabouts the feel and responce is much better than the metro servo. Today is a crap day weather wise so will have to wait for some dry weather to try again.

I am one happy bunny.

Thanks Mike I owe you one and Jason for trying it out and giving the green light. Also thanks everyone on here for all the valuable advice that has helped me with my installation.

[GreatOldOne]

Yay! another happy rabbit in the warren!

Glad it's all working as it should - As for rears locking up before the fronts, the first time I locked the wheels with the test servo I thought that might have been the case - however, with further testing with my installed servo, the fronts definitely lock before the rears. I saw tyre smoke!

[peterux]

Originally Posted by denniswpearce

Today is a crap day weather wise so will have to wait for some dry weather to try again.

.

Hi Dennis,
good to see you got your brakes sorted.

Nice weather today for a good test blast??

...peter

[Chris Cussen]

Sorry to throw a spanner in the works. But before I do let me say I have a cabrio with standard sierra brakes disc/drum setup but without the "deceleration sensitive valve" and I can categorically state that the fronts lock up first on a dry road.

Not withstanding that: the Hayes manual ISBN 1 85960 090 5 "Ford Sierra 1982 to 1993" states in the intro to the braking system (Section 10.1)

"A deceleration sensitive valve on Saloon, Hatchback and Estate Models not fitted with ABS ... is incorporated into th rear brake circuit. The Valve regulates the pressure applied to the rear brakes hydraulic circuit and reduces the possibility of the rear wheels locking under heavy braking"

Section 10.23 of the same manual discribes the removal/refitting but does not detail any deassembly.

So I'm afraid Peter is incorrect in stating Haynes does not mention the dreaded valvle.

BUT it seems in the light of various tests the thing doesn seem to matter one jot.

Sorry to seem like a barrack room lawer.

[peterux]

Originally Posted by Chris Cussen

Sorry to throw a spanner in the works. But before I do let me say I have a cabrio with standard sierra brakes disc/drum setup but without the "deceleration sensitive valve" and I can categorically state that the fronts lock up first on a dry road.

Not withstanding that: the Hayes manual ISBN 1 85960 090 5 "Ford Sierra 1982 to 1993" states in the intro to the braking system (Section 10.1)

"A deceleration sensitive valve on Saloon, Hatchback and Estate Models not fitted with ABS ... is incorporated into th rear brake circuit. The Valve regulates the pressure applied to the rear brakes hydraulic circuit and reduces the possibility of the rear wheels locking under heavy braking"

Section 10.23 of the same manual discribes the removal/refitting but does not detail any deassembly.

So I'm afraid Peter is incorrect in stating Haynes does not mention the dreaded valvle.

BUT it seems in the light of various tests the thing doesn seem to matter one jot.

Sorry to seem like a barrack room lawer.

No Chris, I'm sorry but you seem to have misunderstood my original concern.

I was concerned about a Residual Pressure Valve that is fitted to some brake master cylinders designed for rear drum brakes.

I am fully aware of deceleration sensitive valves and/or Load apportioning valves used to regulate the amount of pressure applied to the rear brakes. These are fitted to most cars including the Sierra and BMW donors. These are desirable and most of the recently built BMW Sportsters have the BMW valve fitted to pass the SVA/IVA tests.
For the avoidance of any doubt to anyone else, DO NOT REMOVE these valves.

My concern was about an inbuilt Residual Pressure Valves (RPV) which have been reported as causing a problem when used with rear disk brakes.

It seems that the Sierra M/C doesn't have an RPV, so it was a non issue.

I hope that is clear now?

[denniswpearce]

Hi Peter,

Yes, you are right it was a good day for a blast, so I did.

I do like the new brakes, have almost forgotten how much pressure I had to use before, the pedal has so much more feel to it, longer travel than before but its better.

The wheels do lock up and the front just locks before the rear does, there is a light pull to the offside which should be correctable and I must look at that. Only did it twice as tyres are an expensive replacement. Its alright for the top gear boys to burn rubber, someone else is paying for the tyres.

Those of you yet to replace your servo,s will not regret it.

[MartinClan]

Completed mine today. Much the same results as everyone else. Easy to lock brakes now (albeit I only tried at 20mph as I was driving down the cul-de-sac where I live).

Brake pedal travel is longer but I suspect some of it could be adjusted out. I think there is probably an inbuilt "gap" in the servo before it does anything - unlike the Metro.

No more to say really than has already been said. One surprise I had though. When I removed the BMW MC I found that it too has 3 ports with one of them being plugged by the manufacturer. That gives me more confidence that doing the same on the Ford MC is fine.

I will post up a couple of pictures tomorrow.

Robin

[MartinClan]

Originally Posted by MartinClan

I will post up a couple of pictures tomorrow.
Robin

And here they are....





The fit is so good it looks like it was made especially for the Sportster. Well done (again) all those that were involved with the selection and design of the bits!

Robin